Plasti Dip Create Your Color
I am so excited because my Plasti Dip Create Your Color arrived at my local Ace Hardware. It has been since 2005 since I last worked with plasti-dip. Back then, there where only 5 colors available. I played around and mixed and created colors but I needed several containers and it was messy. It was fun and I got to mess around with colors and even applied a drip pattern which added grip and a “one of a kind” look to some screw drivers.
With this kit, I just have a large can of clear and I pour what I need into one container and add the tints required toachievethe color I want. My first technique is going to be applying with a paint brush. I do this because if I am only mixing one ounce of a color and I need to dip a nine inch handle, it is not practical to dip the tradional way.
When mixing in the tint, start with the lightest color first. Different colors of tint have different intensities. For instance the yellow tint is easily overcome by the slightest amount of blue. You do not necessarily get grass green from equal portions of blue and yellow.
To apply by brush, you need to thin with 20% thinner to 80% Plasti-Dip. Solvents that can be used are VM&PNaphtha, Toluene, And Xylene. The temperature the day of the brushing was 63 degrees Fahrenheit so I chose Naphtha because it is the fastest evaporating of the three. Dipping, especially after addition of solvents, is an endeavor best carried out in the outdoors. The naphtha is also less toxic than the aromatic hydrocarbons xylene and toluene. It does bear mentioning that thenaphthasolvent smells like gasoline or lighter fluid, not necessarily my favorite smell.
The Verdict
If you want to dip with a limited quantity of dip, brushing is a good application method with minimal equipment. There are some drawbacks to consider though. You need to apply the dip in thick coats and if you hang your work pieces like I do, you need some newspaper to catch drippings. Another point is the cleanup. There will be a significant use of solvents to cleanutensils. To cut back on the thinner used is to use disposable containers. That way, you only need to clean the brush. Next time I will evaluate spray application.
FAQs
PlastiDip can be dipped, brush coated and sprayed.
How to properly apply Plasti Dip? ›
Liquid Plasti Dip should be thinned 50/50 by weight. Apply the first coat as a mist coat and gradually build up the layers. The thicker the final coating, the easier it is to remove in the future should you wish. For vehicles, we suggest a minimum of 6-7 coats.
Is 2 coats of Plasti Dip enough? ›
When following the directions, you can apply as many coats of Plasti Dip protective coating as you like. In most uses 10-12 mils thickness is adequate (2 dip coats, 3-4 brush coats, 4-5 spray coats). Greater thickness might be necessary for aesthetic reasons or in extreme cases.
Do I need to use primer before Plasti Dip? ›
IS PRIMING NECESSARY? Most items being dip coated do not require priming because the coating is shrinking around the item as it dries. However, in extreme conditions or when adding protective coating to a large metal surface, primer is recommended. Use Plasti Dip Primer or a high quality acrylic auto body-type primer.
How to make Plasti Dip dry faster? ›
“Can you speed up the dry time of Plasti Dip ?” Very low oven heat (between 100° – 150°) may be used on a conveyor. However, the part or object should first set or hang dry for 30 minutes for the fast releasing solvents to escape.
What is the best temperature for Plasti Dip? ›
Ideal conditions are low humidity, 70 degrees, little to no air movement in a well-ventilated area.
How long before washing Plasti Dip? ›
Give your dipped surface a full 48 hours to dry before you wash it with DYC materials. Also it's best to avoid automatic/drive in car washes.
Does Plasti Dip cover imperfections? ›
Plastic dip works the same way regular paint does when it comes out the can, so if you start with a scratched surface then you will just be adding to each layer in an uneven pattern. If you are painting over a car with scratches then you can lightly sand the area to even it out and then just clean it and spray over it.
How well does Plasti Dip hold up on a car? ›
DINGS AND DAMAGE. Aside from a few rock dings in the hood and a few other spots around the body where rocks have hit, the PlastiDip has held up very well. The most damage is to the hood and the backs of the side mirrors, which is what we would expect to have the most damage.
Can Plasti Dip be glossy? ›
Yes, the Plasti Dip Enhancer in the Glossifier™ formulation provides a glossy finish on cured Plasti Dipped items.
Many surfaces such as aged paint, oxidized paint, primer, bondo, repainted surfaces, repaired surfaces, aftermarket wheels, aftermarket emblems, fiber glass, plastics, etc are successfully dipped and peeled quite often; however all of our rigorous testing and development is aimed towards usage over good condition OEM ...
Does Plasti Dip come off when washing? ›
Once again, if the Plasti Dip has been properly applied, has had time to cure, and isn't peeling, a trip through the average automatic car wash will have no negative impact on it. The various scrubbers, sprays, buffers, and so on should not pose a problem.
Does Plasti Dip come off with water? ›
If you notice small pieces of Plasti Dip, scrub them off with a cloth dampened in warm water.
Can you use a regular paint sprayer for Plasti Dip? ›
Can I apply Plasti Dip with a conventional paint sprayer? Yes, it is possible to apply Plasti Dip with a conventional air spray gun, HVLP gun or airless paint sprayer.
To apply by brush, you need to thin with 20% thinner to 80% Plasti-Dip. Solvents that can be used are VM&PNaphtha, Toluene, And Xylene. The temperature the day of the brushing was 63 degrees Fahrenheit so I chose Naphtha because it is the fastest evaporating of the three. Dipping, especially after addition of solvents, is an endeavor best carried out in the outdoors. The naphtha is also less toxic than the aromatic hydrocarbons xylene and toluene. It does bear mentioning that thenaphthasolvent smells like gasoline or lighter fluid, not necessarily my favorite smell.